All Inventory

Item Number Manufacturer Quantity Size Style Category Details
5142 NRM 67 40.5" 300-40.5 Autoform Bagwell Tire Press Mechanical Sixty Seven (67) NRM 300-40.5 Autoform_Mechanical_Tire_Tyre_Presses, SMO segmented mold, 300,000lbs ...
5030 McNeil 3 900-36x30 Passenger / LT Tire Bladder Press One (1) Used McNeil Tire Tyre Bladder Press, Model 900 - 36 x 30, closing force 900,000 lbs (450 ton...
5122 NRM 1 6 x 6 150x150 Duplex Tread Extruder Tire Tread Department Item 5122 - One (1) Used NRM 6 x 6 Duplex Extruder, 20” wide tread head, Reliance 100HP DC 1750/2000...
5149 McNeil 4 42" 300-42 BOM Bagomatic Tire Press Mechanical Four (4) Used McNeil Model 300-42 M15, 42" Tire Curing Press, BOM Bagomatic standing post type infla...
5102 Spadone 1 PCR Buffer Tire Inspection Testing One (1) New Unused Spadone, tire_buffer_sidewall_grinder, passenger light truck tire tyre, 12-18" ch...
6032 NRM 1 3 1/2" 90mm 3.5" 12:1 L/D Extruder Cold Feed One (1) Rebuilt NRM 3.5" 90mm 3 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 75 HP 1750 RPM 500 VDC mot...
6075 NRM 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Cold Feed One (1) Used NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 24.68:1 G/B ratio, 100 HP DC...
2060 Bolling 1 20 x 48 500x1200 2-Roll Mill One (1) Used Bolling 20" x 48" 500mm x 1200mm Rubber Mill, rubber mixing mill, motor 125 HP DC, 230v...
6170 NRM 1 3 1/4" 80mm 3.25" Hot Feed Extruder Hot Feed One (1) Used NRM 3.25” 80mm 3 1/4" Hot_Feed_Rubber_Extruder, 4:1 L/D, no motor
2555 Bolling 4 26" Dia Rolls Stock Guides Mill Parts One (1) Used Complete set of stock guides for an Adamson 26” x 26” x 84", 650mm x 2100mm, roller mil...
6711 Werner & Pfleiderer 1 58mm Twin Screw 16:1 Extruder Twin Screw One (1) Used Werner & Pfleiderer 58mm Twin Screw Extruder, twin screw compounder, continuous mixer, ...
6199 KSBI 1 12" 300mm Hot Feed Extruder Hot Feed One (1) Used KSBI 12” (300mm) Hot Feed Rubber Extruder, Lufkin 38.9:1 gearbox ratio, GE motor
6194 Farrel 1 10" 250mm ROLLER FEED Extruder Hot Feed One (1) Used 10" Farrel Hot Feed Rubber Extruder, roller feed, Motor 200 HP, 500 volt, 1750 rpm.
9010 Midlands 1 18" 450mm Two Heads Inner Tube One (1) Used 18" SPLICER MIDLANDS # 900-OH-2675 TWO HEADS
6420 Farrel 1 6" 150mm Head Strainer Straining Extruder Parts One (1) Used Farrel 6" 150mm strainer head (head only, extruder can be quoted seperately)
6430 Farrel 1 12" x 32" 450x800 Head Sheet Sheeting Extruder Parts One (1) Used Farrel 12" Extruder head for making up to 32" wide sheets
6072 NRM 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Cold Feed One (1) Used NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 30.30:1 G/B ratio, 125 HP DC...
4265 Mount Hope 1 6" x 76" 150x1700mm Banana Roll Assembly Calender Parts One (1) Mount Hope Banana Roll Assembly 6" x 76" 150x1700mm, material speader with curved rolls for ...
4267 Litzler 1 66 Material Width Fabric Steering Rolls Calender Parts One (1) Used Litzler Fabric edge guides for a 66" material width fabric calender line
4277 Boschert Bosch 1 2” 50mm Chuck Calender Parts One (1) Used Boschert Bosch 2” Chuck for wind-up let-off
4275 Litzler 1 66" Material Width Pull Roll Stand Calender Parts One (1) Used Litzler Pull Roll Stand, low tension, 10 HP, FALK reducer, three (3) driven rolls, new ...
1860 Farrel 1 F270 Connecting Gears Unidrive Mixer Parts One (1) Used set output shafts from Farrel F270 or #11D gearbox, includes 46/41 tooth herring bone c...
1875 Farrel 1 F270 11D Coupling Unidrive Mixer Parts One (1) Used Farrel set of F270 unidrive couplings, 53 Tooth.
4273 Spadone 1 72 wide 1830 Prick Roll Calender Parts One (1) Used Prick Roll Assembly for rubber calendar, 72” wide, 48” accumulator, removable pins, air...
2560 Adamson 1 19/23T 1DP Connecting Gears Mill Parts One (1) NEW Set of connecting gears with 21" centers, 19/23 tooth, 1 DP, 12/10" bore, 12" face, suit...
7320 Siemens 1 450 HP DC Motor One (1) Used Siemens 450HP (335KW) 1460/1680RPM, 520V DC Motor, Frame TGH5312-ONG10-7MU5-Z
6419 RMS 1 8" x 24" 200x600 Head Roller Die Extruder Parts One (1) Used RMS_Rollerdie_head_for_8” x 24" extruder.
5111 RMS 1 23" Width Roller Die Head Tire Tread Department One (1) used RMS roller die head, 6” ID inlet mating with extruder, 23” roll face, approximately 20”...
6424 Farrel 1 8" x 38" 200x965 Head Sheet Sheeting Extruder Parts One (1) Used 8" extruder head for making up to 38" wide sheets.
2575 Lufkin 2 9" Bore Coupling Mill Parts Two (2) Used 9" Bore couplings, 28 teeth.
2576 Farrel 1 15" Bore Coupling Mill Parts One (1) Used 15" bore 28 teeth coupling.
1930 Farrel 1 11A End Frames Mixer Parts One (1) Used Farrel_11A_Slide_door end frames.
2574 Farrel 1 6" Bore Coupling Low Speed Mill Parts One (1) Used 6" Bore 30 teeth coupling.
6432 RMS 1 23" Width Head Roller Die Extruder Parts One (1) Used RMS Roller die head, single roll roller die, 6” ID inlet mating with extruder, 23” roll...
8180 Farrel 1 150 HP 38.7:1 Parallel Shaft Gearbox Reducer One (1) Used Farrel gearbox, 151 HP, 38.7:1 reduction ratio, size DR-33, input 1200 RPM
7520 Siemens 1 75 HP Drive Panel Motor Drive Panel One (1) Used Siemens 75 HP Microprocessor DC drive, S/N 16-96-D3607501-01.
2577 Farrel 1 16" Bore Coupling Mill Parts One (1) Used Low Speed Coupling 16" 40 teeth coupling.
1700 Torrington 1 11D Bearings Anti-friction Mixer Parts One (1) Rebuilt Bearings Torrington set of number 11D mixer bearings, part number 23156 W33.
1903 Soberay 1 11D Dust Seals SSA Mixer Parts Four (4) New dust seals for 11D mixer, 4 teflon rings, 24 springs, 4 floating ring keys.
1905 Soberay 4 F270 Dust Seals FYH Mixer Parts Four (4) New dust seals for F270 mixer,FYH style.
2024 Adamson 1 16 x 36 400x915 2-Roll Mill One (1) Used Adamson 16 x 36, 400mm x 915mm, Rubber Mill, rubber mixing mill, silicone mill, Jones_G...
6117 Berstorff 1 8" 200mm 8.0" Cold Feed 12:1 Extruder Silicone One (1) Used Berstorff 8" (200mm) Cold Feed Silicone Extruder, 12:1 L/D, 250 HP, 1150 RPM, 460 VAC m...
6174 Royle 1 4 1/2" 120mm 4.5" Hot Feed Extruder Hot Feed One (1) Used Royle 4.5" 120mm 4 1/2" Hot Feed Rubber Extruder, 4:1 L/D, Motor 100HP AC, swing gate ...
6074 NRM 1 4 1/2" 90mm 4.5" 17:1 L/D Extruder Cold Feed One (1) Rebuilt NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 17:1 L/D, 125 HP DC 1150/2000RPM 50...
4240 Honeywell 1 84" Sheet Max. Gap Measurement System Calender Parts One (1) Used Honeywell Measurex MX ProLIne measurement and control system 8450, Beta gage, Model up...
4325 Joh. Peter Falter 1 48" 1200 Sheet Slitter Calender Parts One (1) Used Joh. Peter Falter (Germany) sheet slitter_with_adjustable_rotary_blades, 48”, 1200mm, m...
1920 Farrel 1 11D Hopper Pneumatic Mixer Parts One (1) Used hopper cylinder and floating weight for an 11D mixer, floating weight dimensions 11.5" ...
1950 Torrington 1 F270 11D Bearings Anti-friction Mixer Parts One (1) Used_assortment_of_Torrington and SKF mixer bearings for 11D/F270 mixers, please contact us ...
1735 Farrel 1 3D Rotors Unidrive Mixer Parts One (1) Used set of Farrel 3D rotors, 2-wing, unidrive, SSA dust seal configuration.
1770 Farrel 1 F270 Rotors Unidrive Mixer Parts One (1) used set of Farrel F270 rotors, 4-wing type, unidrive configuration.
3160 Adamson 1 48 x 48 1200x1200 4 - Post Parts Press Hydraulic Press Parts One (1) Used Adamson_48_x_48_4–Post hydraulic press, 30” ram, 45” stroke, Parts Only.
3165 Adamson 1 48 x 48 1200x1200 4 - Post Parts Press Hydraulic Press Parts One (1) Used Adamson 48" x 48" 4 - post hydraulic press, 30" ram, 60” stroke, no rods, parts only
1750 Farrel 1 11D Rotors Bull Gear Mixer Parts One (1) used set of Farrel 11D bull gear rotors
1925 Bainite 1 F370 Hopper Pneumatic Mixer Parts One (1) New Bainite Hopper for F370 litre mixer, 24” x 37.5” floating weight opening (weight not inc...
8259 Philadelphia 1 200 HP 35:1 Parallel Shaft Gearbox Reducer One (1) Used Philadelphia Gearbox Reducer, 200 HP service rating, 35:1 reduction ratio, 1.5 SF serv...
8260 Falk 1 200 HP 142:1 Parallel Shaft Gearbox Reducer One (1) Used Falk Gearbox Reducer, 200 HP service rating, 142:1 reduction ratio, 1.5 SF service fac...
8320 Amcot 1 400 HP 31.66:1 Parallel Shaft Gearbox Reducer One (1) Used Amcot Gearbox Reducer, 400 HP service rating, 31.66:1 gearbox ratio, 600 RPM Input, Cen...
8360 Santasalo 1 500 HP 25.36:1 Parallel Shaft Gearbox Reducer One (1) Used Santasalo Gearbox Reducer, 500HP (373kw) Service Rating, 25.36 Ratio, new 1996. Motor a...
8140 Dominion 1 150 HP 11.1:1 Parallel Shaft Gearbox Reducer One (1) Used_Dominion_Gearbox_Reducer 150 HP, 11:1 ratio, previously used on a 22x20x60, the output ...
7300 Reliance 1 250 HP AC Motor OOne (1) Used Reliance Motor, 250 HP AC, 1780 RPM, 460 Volts, ID No. 917480A4, 60 HZ, 282 Amps
7273 General Electric 1 200 HP AC Motor One (1) Used General Electric Motor, 200HP AC, 700 RPM, 440 Volts, Frame 82668
7125 Westinghouse 1 100 HP AC Motor One (1) Used Westinghouse Motor, 100HP AC, 1770 RPM, 440 Volts, 130 Amps, 3 phase, 50 cycle
6330 Farrel 1 18x15" 450x375 Drop Extruder Strainer Extruder Dump One (1) Rebuilt Farrel 18x15" Rubber Dump Extruder Strainer, Drop Extruder, 29.2 G/B ratio Rebuilt 4...
2028 Kobe 1 21 x 36 533x914 2-Roll Mill One (1) Used Kobe 21” x 36” (533 x 914) Rubber Mill, MILL BODY ONLY, friction ratio between rolls 1...
2162 Farrel 1 26 x 38 660x965 Mill Cracker Mill Cracker One (1) Farrel 26" x 26” x 38”, 660mm x 965mm, Cracker_Mill_Bare_Machine, corrugated front and rear ...
4031 Bolling 1 20 x 48 500x1200 Horizontal Calender 2-Roll One (1) Used Bolling 20” x 48”, 500mm x 1200mm, 2-Roll Rubber Calender, Westinghouse 125 HP DC, 240v...
4021 Kobe 1 21 x 36 533x915 Horizontal Calender 2-Roll One (1) Used Kobe 21” x 36”, 533mm x 915mm, Rubber Calender, gearbox 32:1 reduction ratio, friction...
8050 Farrel 1 6 x 13 150x330 Lab Mill Lab Equipment One (1) Used Farrel Rubber Lab Mill, 6 x 13” (150 x 330) rolls, cabinet style, under-slung drive, be...
8063 Bolling 1 8 x 16 200x400 Lab Calender Lab Equipment One (1) Used Bolling 8 x 16 Inverted "L" Rubber Calender, individual 10 HP 550v - 1750 RPM direct d...
8075 PHI 1 9 x 12 225x300 Lab Press Lab Equipment One (1) Rebuilt PHI Lab Press with the following features. New platens size 9” x 12” with 3 heaters...
6071 NRM 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Cold Feed One (1) Rebuilt NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 25.14:1 G/B ratio, 100 HP...
3130 Valves 5 3" 75 Valves for Hydraulic Compression Press Hydraulic Press Parts Five (5) Used Valves 3" pipe for Hydraulic Compression Press, previously used on a 48" x 48" press ...
4274 Spadone 2 44" 1100 Calender Wind-up Stand Calender Parts Two (2) Used Spadone 44” Calender Cantilever Wind-up Stand, 4-stations available, previously used fo...
6460 Berstorff 1 8" 200mm Screw Extruder Parts One (1) New Berstorff 8” 200mm 12:1 L/D Screw, high output design for polymer extrusion.
1873 Farrel 1 F270 11D Coupling Half Mixer Parts One (1) Used Coupling Half for #11D or F270 Mixer, 68T tooth, 15.5” bore
4291 Spadone 1 48" 1200 Automatic Splicer Calender Parts One (1) Used Spadone 48” Automatic Splicer, previously used with a Spadone bias cutter
1926 Farrel 1 F270 11D Hopper Rod/Ram Mixer Parts One (1) Used Farrel Hopper Rod / Ram for a 20”, 500mm, hopper, rod 3.5” x 80” commonly used on #11D ...
1927 Farrel 1 11D F270 Hopper Rod/Ram Mixer Parts One (1) Used Farrel Hopper Rod / Ram for a 20”, 500mm, hopper, rod 3.5” x 84” commonly used on #11D ...
2590 Farrel 2 17" bearing, 23" window height Journal Box Housings Mill Parts Two (2) Used Farrel Journal Box Housings, 17” bearing, 23” window height
2591 Farrel 2 17" bearing, 25" window height Journal Box Housings Mill Parts Two (2) Used Farrel Journal Box Housings, 17” bearing, 25” window height
8099 Falk 1 40 HP 69:1 Right Angle Gearbox Reducer One (1) Used Falk Gearbox Reducer, 40HP, 69:1 ratio, right angle, previously used on a cushion calen...
3127 Eemco 6 58 x 52 x 3 1450x1300x75 Steam Platens for Hydraulic Compression Press Hydraulic Press Parts Six (6) Used Eemco 58" x 52" x 3" Steam Platens for Hydraulic Compression Press
2550 Renold 6 26" Dia Rolls Low Speed Chain Mill Parts One (1) Used Renold 200 Cottered Roller Chain, figure 8 / curved side bar, 2-1/2” pitch (pin-to-pin)...
1919 Farrel 1 11D Hopper Pneumatic Mixer Parts One (1) Used Farrel 11D Pneumatic hopper with floating weight for an 11D mixer, 22” cylinder, floati...
1938 Trabon 1 11D F270 Lubrication Panel Process and Lube Mixer Parts One (1) Used Trabon Process and Lube Lubrication Panel for #11D or F270 Mixer, Rexroth valves, Lubri...
1955 KSBI 1 11D Base Mixer Parts One (1) Used KSBI Base for #11D mixer, fabricated plate base, drop door type
6175 NRM 1 6" 150mm Hot Feed Extruder Hot Feed One (1) Used 6" NRM Hot Feed Rubber Extruder, Motor Reliance 100 HP DC, 500 volt, 1750/2000 rpm, Gea...
3129 Venango 2 42 x 150 x 3 Steam Platens Hydraulic Press Parts Two (2) Used Venango 42" x 150" x 3" Steam Platens for Hydraulic Compression Press
2149 Farrel 1 28 x 100 700x2500 2-Roll Roller Bearing Mill One (1) Used Farrel 28x28x100” single mill, rubber_mixing_mill, ROLLER BEARING, anti-friction bearin...
6181 NRM 1 8" 200mm Hot Feed Extruder Hot Feed One (1) Used 8" NRM Hot Feed Extruder, right hand feed, pneumatically adjustable sheet head, GB rati...
3036 TMP 1 15 x 15 375x375 60 Ton Self Contained Hydraulic Press One (1) Used TMP 15" x 15" 375mm x 375mm Rubber Hydraulic Lab Press, 8" ram, 60 ton, 18" daylight, 1...
4009 Bolling 1 8 x 20 200x500 Vertical Calender 2-Roll One (1) Used Bolling 8" x 20”, 200mm x 500mm, 2-Roll Rubber Calender, Silicone Calender, chrome rol...
5293 4JET 1 25-49" Tire OD Passenger & Truck Tire Laser Engraver One (1) New 4JET Laser Tire Tyre Engraving Machine, Model T-MARK 1600 Tire Marking System, compact d...
2064 Adamson 1 20x22x60 1500mm 2-Roll Mill One (1) Used Adamson 20” x 22” x 60” 2-Roll mill, Falk 6.389:1 single reduction gearbox, bull gear d...
8361 Lufkin 1 540 HP 37.5:1 Parallel Shaft Gearbox Reducer One (1) Used Lufkin T720 BH Gearbox Reducer, 540 HP service rating, 37.5:1 reduction ratio, 1.5 SF s...
4019 Farrel 1 24 x 68 610x1725 Vertical Calender 3-Roll One (1) Used Farrel 24x68" 3-Roll Rubber Calender, General Electric 150 HP, 850/1700 RPM, 500 VDC mo...
6601 Barwell 1 C3 Preformer Extruder Preformer One (1) Used Barwell C3 Preformer, Barwell_Rubber_Preformer, capacity 120 lbs, 10" x 55" chamber, Mo...
1037 TMP 1 75 Liter Litre Kneader Tilt Mixer One (1) Rebuilt TMP Technical Machine Products Techni-Mix 75 Liter Litre Rubber Tilt Mixer, 200 HP D...
6491 Mokon 1 9 KW Model DT4009GG TCU One (1) Used Mokon TCU, 1 zone, one (1) motors 1.9 amps, 460V, heater 11.3 amps, total amps 13.2, to...
1022 Bolling 1 OO 1.6L Litre Lab Mixer Mixer One (1) Used Model Bolling Lab Banbury Mixer, 1.6 liter, 2.6 lb. capacity, 96 cu. in net volume of m...
6449 NRM 1 3.5" 90mm Screw Extruder Parts One (1) Used NRM Plastiscrew 3.5” 90mm 17:1 L/D Screw, plastiscrew design for rubber extrusion.
6469 Farrel 1 18" x 15" Screw Extruder Parts One (1) Used 18" x 15" Screw for Farrel Dump Extruder
1584 Torrington 1 11D F270 Bearings Anti-friction Mixer Parts Torrington Mixer Bearings One (1) used set of number 11D F270 mixer bearings, part number 23156 W33....
4029 Allen 1 16 x 48 400x1220 Vertical Calender 2-Roll One (1) Used Allen 16” x 48”, 400mm x 1220mm, 2-Roll Rubber Calender, drive can be built to suit.
8319 Alten 1 400 HP 30:1 Unidrive #4 Bolling Gearbox Reducer One (1) Used Alten Gearbox 30:1 ratio, 400 HP @ 1200 RPM, 1.75:1 service factor, parallel shaft, dua...
1891 Farrel 1 11A Door Top Mixer Parts One (1) Used Farrel 11A Mixer Doortop with cylinder assembly.
6520 Davis Standard 1 1.5" 38mm 30:1 L/D Extruder Plastic One (1) Used 1.50" 38mm Plastic Extruder, 30:1 L/D ratio
6405 NRM 1 10" Barrel Extruder Parts One (1) New NRM Barrel for NRM 10" hot feed extruder, non-roller feed type
6423 NRM 1 8" 203mm Head Sheet Sheeting Extruder Parts One (1) Used NRM Sheeting Head for 8" NRM or Davis Standard rubber extruder, produces up to 20" wide...
1681 Farrel 1 11A 11D Bull Gear & Pinion Mixer Parts One (1) Used Mixer bull gear and pinion for 11D mixer. 20” face 108 tooth bull gear, 22 tooth pinion...
6113 Troester Monsanto 1 6" 150mm 6.0" 18:1 L/D Extruder Cold Feed One (1) Used Troester / Monsanto 6" 150mm Cold Feed Rubber Extruder, 18:1 L/D, 250 HP, 1750 RPM, 500...
1455 Farrel 1 #11D Body Chamber Mixer Parts One (1) Used Farrel #11D unidrive chamber only, 237 liter capacity, 2-wing rotors, SSA dust stops, d...
7399 General Electric 1 2500 HP AC Motor One (1) Used GE Motor 2500 HP @ 885 RPM input, 2300V, Frame 8511SU
3025 PHI 1 9 x 12 225x300 18 Ton Hand Pump Hydraulic Press One (1) Rebuilt PHI hand pump style 18-ton hydraulic lab press. New platens size 9” x 12” with 3 he...
2146 Farrel 1 28 x 84 700x2130 2-Roll Mill One (1) Used Farrel 28 x 84 (710 x 2130) Rubber Roller Mill, Falk Gearbox with 51.49 reduction ratio...
2068 Adamson 1 22 x 60 560x1500 2-Roll Mill One (1) Used Adamson 22” x 22” x 60” 2-Roll mill, break down mill, corrugated rear roll, motor 75 HP...
1065 Bolling 1 #10 195 Liter Litre Tangential 2-Wing Mixer One (1) Used Bolling #10 Rubber Mixer, 195 liter chamber, 350 lb batch, 2-wing tangential rotors, 60...
9065 Joh. Peter Falter 1 48” max material width Shear Cutter Cutter Item 9065 - One (1) Used Joh. Peter Falter (Germany) shear cutter, 48” max material width, pull roll...
9058 Joh. Peter Falter 2 48” wide Pneumatic Slitter Slitter Item 9058 - One (1) Used Joh. Peter Falter (Germany) 48” wide pneumatic slitter, adjustable width
2563 Farrel 1 27T, 1DP Connecting Gear Mill Parts One (1) Used Farrel Connecting Gear 27T, 1DP, 14.5” face
2564 Farrel 1 27T, 1DP Connecting Gear Mill Parts Item 2563 - One (1) Used Farrel Connecting Gear 27T, 1DP, 15” face
2573 Lufkin 1 5-1/2” & 8-12” bores Coupling Low Speed Mill Parts One (1) Used Low Speed Coupling Set with chain, 5-1/2” & 8-12” bores, 20 teeth, excellent condition...
2578 Custom 1 26" Dia Rolls Low Speed Wobbler Coupling Set Mill Parts One (1) Used Farrel Low Speed Wobbler Coupling Set, previously used on a 26x84” mill.
1858 TMP 1 75L Connecting Gears Mixer Parts One (1) Used Set of Connecting Gears for a TMP 75L tilt mixer
1884 Farrel 1 F270 Floating Weight Mixer Parts One (1) Used Floating Weight for Farrel F270 Mixer.
8115 Alten 1 75 HP, 86.5:1 Parallel Shaft Gearbox Reducer One (1) Used Alten Model TG-320A-2-87 Gearbox Reducer, 75 HP service rating, 86.5:1 reduction ratio,...
6500 Tempco 4 230V, 6” bore, 14” length Heater Extruder Parts One (1) NEW Tempco Electrical Cast-In Heater, band heater for Davis Standard extruder barrel, item ...
3810 Parker Hannifin 1 5 HP 230/460V Power Unit Division Hydraulic Press Parts One (1) Used Parker Hannifin Hydraulic Unit, Power Unit Division, 5 HP 230/460V motor, Sperry Vicker...
1885 Farrel 1 F270 Floating Weight Mixer Parts One (1) Rebuilt Floating Weight for Farrel F270 Mixer
1888 Farrel 1 11D Mixer Door Support Mixer Parts One (1) used Farrel Door Support for #11D Mixer, includes door shaft
1892 Farrel 1 11D Mixer Door Top Mixer Parts One (1) Used Farrel 11D Mixer Door Top
1918 Farrel 1 F200 Mixer Pneumatic Hopper Mixer Parts One (1) Pneumatic Hopper for a Farrel F200 mixer, includes floating weight.
1937 Trabon 1 F270 Mixer Trabon Process and Lube Lubrication Panel Mixer Parts One (1) Used Trabon Process and Lube Lubrication Panel for #11D or F270 Mixer
8110 Falk 1 60 HP 36.44:1 Parallel Shaft Gearbox Reducer One (1) Used Falk Model 2100Y83-3 Gearbox Reducer, 60 HP service rating, 36.44:1 reduction ratio, 1....
8111 Foote Bros 1 60 HP 14.2:1 Parallel Shaft Gearbox Reducer One (1) Used Foote Bros Brothers Model 100-DX Gearbox Reducer, 60 HP service rating, 14.2:1 reductio...
8136 D.O James Gear 1 139 HP 36.44:1 Parallel Shaft Gearbox Reducer One (1) Used D.O James Gear Model 270HS Gearbox Reducer, 139 HP service rating, 9.07:1 reduction rat...
8139 Lufkin 1 150 HP 35:1 Parallel Shaft Gearbox Reducer One (1) Used Lufkin Gearbox Reducer, 150 HP service rating, 35:1 reduction ratio, 1.5 SF service fac...
8255 Pierce Pingon 1 200 HP 28.29:1 Parallel Shaft Gearbox Reducer One (1) Used Pierce Pingon Gearbox Reducer, 200 HP service rating, 28.29:1 reduction ratio, 228 lbs ...
8266 Falk 1 300 HP 9.354:1 Parallel Shaft Gearbox Reducer One (1) Used Falk Model 155Y2-A Gearbox Reducer, 300 HP service rating, 9.354:1 reduction ratio, 1.4...
8359 Flender 1 500 HP 13.88:1 Parallel Shaft Gearbox Reducer One (1) Used Flender Model SZN500 Gearbox Reducer, 500 HP service rating, 13.881:1 reduction ratio, ...
7148 Alloy Craft OTR Chamber 1 140"Dia x 112"L Steam Autoclave Item 7148- One (1) Used Alloy Craft 140” ID Steam Autoclave Vulcanizer, OTR chamber for retreading, ...
4134 Farrel 1 12 x 24 300x600 Inverted "L" Calender 4-Roll One (1) Used Farrel 12 x 24 4-Roll Inverted “L” Calender, GE 100 HP 1750/2200 RPM 500 VDC motor, dir...
2650 Farrel 1 24" x 66" 600x1650 Calender Roll Rolls One (1) Used Farrel 24x66” Calender Roll, middle roll, drilled for cooling, 32” shaft and 45” long ...
2655 Farrel 1 28" x 75" 700x1875 Calender Roll Rolls One (1) Used Farrel 28” x 75” Calender Roll, middle roll, cored for cooling, 19” bushing journals, s...
2663 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 15” co...
2664 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 15” co...
2665 Farrel 1 26" x 84" 650x2100 Mill Roll Rear Corrugated Rolls One (1) Used Farrel 26” x 84” Mill Roll, rear roll, cored for cooling, 17” bushing journals, corrug...
2675 Farrel 4 28” x 86” 700x2150 Calender Roll Rolls One (1) Used Farrel 28” x 86” Calender Roll, drive roll, drilled for cooling, roller bearing journal...
6402 NRM 1 4.5” 120mm Barrel Extruder Parts One (1) Used Spare Barrel for NRM 4.5” 120mm 12:1 L/D cold feed rubber extruder.
6403 NRM 1 4.5” 120mm Barrel Extruder Parts One (1) Used Spare Barrel for NRM 4.5” 120mm 12:1 L/D cold feed rubber extruder
6447 NRM 1 3.5” 90mm Plastiscrew Extruder Parts One (1) Used NRM Plastiscrew 3.5” 90mm 17:1 L/D Screw, plasticscrew design for rubber extrusion
7126 General Electric 1 100 HP DC Motor One (1) Used General Electric Statohm Motor, 100 HP DC, 1150/2000 RPM, 550 Volts, 146 Amps, class F ...
6448 NRM 1 3.5” 90mm Plastiscrew Extruder Parts One (1) Used NRM Plastiscrew 3.5” 90mm 17:1 L/D Screw, plasticscrew design for rubber extrusion
6451 NRM 1 4.5” 120mm Plastiscrew Extruder Parts One (1) Used NRM Plastiscrew 4.5” 120mm 12:1 L/D Screw, plasticscrew design for rubber extrusion
6452 NRM 1 4.5” 120mm Plastiscrew Extruder Parts One (1) New NRM Plastiscrew 4.5” 120mm 12:1 L/D Screw, plasticscrew design for rubber extrusion
3126 French 1 60" x 60" x 2" 1500x1500x50 Steam Platen Hydraulic Press Parts One (1) Used French 60" x 60" x 2" Steam Platen for Hydraulic Compression Press
2016 Farrel 1 6 x 13 150x330 Rebuilt Lab Mill One (1) Rebuilt Farrel Lab Mill, 6 x 13” (150 x 330) rolls, cabinet style, under-slung drive, belt d...
9092 Mitts Merrill 1 150 HP Hog Mill Hog Mill One (1) Used Mitts & Merrill Hog Grinder, 5/8” screen, hog mill, 150 HP, 895 RPM, 460 VAC motor, bel...
8321 Lufkin 1 400 HP 40.8:1 Parallel Shaft Gearbox Reducer Item 8321 - One (1) Used Lufkin T720 B Gearbox Reducer, 400 HP service rating, 40.8:1 reduction rati...
1749 Farrel 2 #9 Rotors Bull Gear Mixer Parts One (1) Used set of Farrel #9 rotors, 2-wing, bull gear configuration
1771 Farrel 2 F270 Rotors Unidrive Mixer Parts One (1) Used Set of Farrel F270 rotors, Banbury design, 2-wing type, Unidrive configuration
3026 PHI 1 12 x 12 250x250 18 ton Hand Pump Hydraulic Press One (1) Rebuilt PHI Lab Press with the following features. New platens size 12” x 12” with 3 heaters...
8076 PHI 1 12 x 12 250x250 Lab Press Lab Equipment One (1) Rebuilt PHI Lab Press_with_the_following features. New platens size 12” x 12” with 3 heaters...
8051 Farrel 1 6 x 13 150x330 Rebuilt Lab Mill Lab Equipment Item 2016 - One (1) Rebuilt Farrel Lab Mill, 6 x 13” (150 x 330) rolls, cabinet style, under-slung d...
7269 Allis Chalmers 1 150 HP AC Motor One (1) Used Allis Chalmers Motor, 150HP AC, 585 RPM, 220 Volts, 3 phase, 60 cycle, 376 F.L. amps
2572 Lufkin 2 9" Bore Coupling Low Speed Mill Parts Item 2572 - One (1) used coupling set, 9" bore, 30 teeth, 8” length, LIKE NEW
7311 General Electric 1 300 HP AC Motor One (1) Used GE General Electric Motor, 300 HP, 1180 RPM, 460 VAC, 348 Amp, Model 5K818846C64
4048 Akron Steel Fabricators 1 24 x 68 610x1725 Inclined Calender 2-Roll One (1) Used Akron Steel Fabricators 24x68" 2-Roll Calender, Vickers individual hydraulic drives for...
8411 Lufkin 1 1000 HP 21.85 Unidrive F270 #11D Gearbox Reducer One (1) Used Lufkin model D890AH double reduction horizontal parallel shaft mixer speed reducer, arr...
8393 Lufkin 1 800 HP 22.48 Unidrive F270 #11D Gearbox Reducer Item 8393 - One (1) Used Lufkin model D890AH double reduction horizontal parallel shaft mixer speed ...
8394 Lufkin 1 1000 HP 22.48 Unidrive F270 #11D Gearbox Reducer Item 8394 - One (1) Used Lufkin model D890AH double reduction horizontal parallel shaft mixer speed ...
5015 Bartell 3 16" Bead Winder Tire Bead Winder Three (3) NEW / UNUSED 16” Bartell Bead Winder Chuck, S/N UGF-1662
5014 Bartell 1 15" Bead Winder Tire Bead Winder One (1) NEW / UNUSED 15” Bartell Bead Winder Chuck, S/N UGF-1613
5191 NRM 7 44.5" 350-44.5 Autolok Tire Press Hydraulic Item 5191 - Seven (7) Used NRM 44.5" Autolok Hydraulic Tyre Curing Press, model 350 - 44.5", closing...
1021 Bolling 1 OM 1.6L Litre Lab Mixer One (1) Used_Bolling_Lab_Banbury_Mixer, 1.6 liter, 2.6 lb.capacity, 96 cu. in net volume of mixer ch...
4128 Farrel 1 8 x 16 200x400 Inverted "L" Calender 4-Roll One (1) Used Farrel 8 x 16 4-Roll Inverted “L” calender, 15 HP GE gearhead motor 1750/3000 RPM 200VA...
1001 Farrel 1 Midget Lab Mixer Item 1001 - One (1) Used Farrel Midget Lab Banbury Rubber Mixer, 0.50 liter chamber. Approx 1lb batc...
8412 Lufkin 1 1000 HP 24.1:1 Unidrive F270 #11D Gearbox Reducer Item 8412 - One (1) Used Lufkin model DF850CH double reduction horizontal parallel shaft mixer speed...
8451 Lufkin 1 1300 HP 24.1 Unidrive F270 #11D Gearbox Reducer One (1) Used Lufkin model DF850CH double reduction horizontal parallel shaft mixer speed reducer, ar...
1074 Farrel 1 #11D 236 Liter Litre Tangential 2-Wing Mixer Item 1074 - One (1) Used Farrel #11D 11D Banbury Rubber Mixer, 2-wing tangential rotors, Lufkin DF85...
4069 Bolling 1 32 x 120 810x3045 Vertical Calender 2-Roll One (1) Used Stewart Bolling 32” x 120” 2-Roll Rubber Calender, cored rolls, 100 HP 500 VDC electri...
2023 Bolling 1 14 x 30 355x760 Cabinet Style Mill One (1) Used Bolling Rubber Mill, 14” x 30” (355 x 760mm) rolls, cabinet style, under-slung drive, c...
2026 Bolling 1 16 x 36 400x915 2-Roll Mill One (1) Used Bolling 16 x 36 (400 x 915) Silicone Mill, AC motor with VFD, Falk gearbox, direct driv...
9068 Eemco 1 30" Blade Hydraulic Bale Cutter One (1) Used Eemco 30” Hydraulic Guillotine Bale Cutter, 32" blade length, 18” daylight under blade,...
8365 Lufkin 1 641 HP 40.8:1 Parallel Shaft Gearbox Reducer One (1) Used Lufkin T720 B Gearbox Reducer, 400 HP service rating, 40.8:1 reduction ratio, 1.61 SF s...
8324 Jahnel-Getriebe 1 400 HP 36.4:1 Parallel Shaft Gearbox Reducer One (1) Used Jahnel-Getriebe Gearbox Reducer, replaces Lufkin T720L, 400 HP service rating, 36.4:1 r...
8315 Lufkin 1 400 HP 22.5:1 Parallel Shaft Gearbox Reducer One (1) Used Lufkin D912 Gearbox Reducer, 400 HP service rating, 22.5:1 reduction ratio, 1.5 SF serv...
4004 Bolling 1 6 x 12 150x300 Vertical Calender 3-Roll One (1) Used Bolling 6x12 3-Roll Lab Calender, US Varidrive motor 440 VAC, Cabinet style, under-slun...
5124 Spadone 1 Passenger Truck Tread Skiver Tire Tread Department One (1) Used Spadone Skiver Cutter
6196 NRM 1 10" 250mm ROLLER FEED Extruder Hot Feed One (1) Used 10" NRM Hot Feed Extruder, roller feed, 27.5:1 gearbox ratio
8108 Eurodrive 1 60 HP 46.79:1 Right Angle Gearbox Reducer Item 8108 - One (1) Used SEW-Eurodrive Gearbox Reducer, Type K157AD7, 60 HP service rating, 46.79:1 ...
8119 Philadelphia 1 100 HP 47.1:1 Right Angle Gearbox Reducer Item 8119 - One (1) Used Philadelphia Gearbox Reducer, Size Type 3615, 100 HP service rating, 47.1:1...
5118 NRM 1 6 x 10 150x250 Duplex Tread Extruder Tire Tread Department One (1) used NRM 6” x 10 Duplex Hot Feed ROLLERFEED tread extruder, opposed head, NRM 10” with 27:1 ...
2666 Farrel 1 26" x 84" 650x2100 Mill Roll Rear Half Corrugated Rolls One (1) Used Farrel 26” x 84” Calender Roll, rear roll, HALF CORRUGATED surface, cored for cooling, ...
6111 Krupp 1 6" 150mm 6.0" 18:1 L/D Extruder Cold Feed One (1) Used Krupp 6" 150mm Cold Feed Rubber Extruder, 18:1 L/D ratio, belt driven motor, power feed...
8094 Farrel 1 Midget 0.50L Lab Mixer Lab Equipment One (1) Used Farrel Midget Lab Banbury Mixer, 0.50 lb. capacity, internal mixer, jacketed mixing cha...
6110 Davis Standard 1 6" 150mm 6.0" 20:1 L/D Extruder Cold Feed One (1) Used Davis Standard 6" 150mm Cold Feed Rubber Extruder, 20:1 L/D, gearbox rated at 300 HP, g...
2017 Farrel 1 6 x 13 150x330 Lab Mill Mill One (1) Used Farrel Rubber Lab Mill, 6 x 13”, 150mm x 330mm, rubber mixing mill, cabinet style, unde...
9037 Berstorff 1 86" 2180mm Continuous Cure Rotocure One (1) Used Berstorff 60” x 86” rubber rotocure, main curing drum 60” x 86”, 81” stainless steel be...
1871 Farrel 1 F270 #11D Coupling Half Mixer Parts One (1) Used Coupling Half for #11D or F270 Mixer, 74T tooth, 10.5” bore
1872 Farrel F270 #11D Coupling Half Mixer Parts One (1) Used Coupling Half for #11D or F270 Mixer, 80T tooth, 8.5” bore
1040 Bolling 1 #4 80 Liter_Litre Tangential 2-Wing Mixer One (1) Used Bolling #4 Rubber Mixer, 80 liter, 150 lb batch, gearbox Bolling unidrive double reduct...
2070 Vaughn 1 22 x 60 1500mm 2-Roll Mill One (1) Used Vaughn 22” x 60” 2-Roll Rubber Mill, strip mill, motor 150 HP, 1150-2000 RPM, 500 VDC, ...
1928 Farrel 1 F270 Hopper Pheumatic Mixer Parts Item 1928 – One (1) Used Farrel F270 Pneumatic hopper with floating weight for an F270 Banbury mixer...
1451 Parker 1 11D F270 Linear Actuator Mixer Parts One (1) Used Parker Linear Actuator for Farrel F270 or #11D Mixer
8380 Lufkin 1 600 HP 19.16:1 Unidrive F80 3D Gearbox Reducer One (1) Used Lufkin model DF582 double reduction horizontal parallel shaft Farrel F80 or 3D mixer sp...
8381 Lufkin 1 600 HP 19:1 Unidrive 3D F80 Gearbox Reducer One (1) Used Lufkin model DF582 double reduction horizontal parallel shaft Farrel F80 or 3D mixer sp...
2161 Farrel 1 20x24x32 800mm Mill Cracker Mill Cracker One (1) Farrel 20" x 24” x 32”, Cracker Mill, corrugated front and rear rolls, GE 200 HP DC motor & ...
7332 General Electric 1 600 HP DC Motor One (1) Used GE Motor, 600 HP, 1150 / 1500 RPM, 500 VDC, foot mounted
2192 Bolling 1 20x24x36 Refiner Reclaim Mill Mill Refiner One (1) Used Bolling 20 x 24 x 36” Refiner Mill, 2.5:1 friction ratio between rolls, Westinghouse 12...
2019 Farrel 1 6 x 13 150x330 Lab Mill DUAL DRIVE Mill One (1) Used Farrel Lab Mill, 6 x 13” (150 x 330) rolls, cabinet style, under-slung DUAL DRIVE, indi...
8028 Alpha Technologies 1 Tensometer 2000 Tensile Tester Lab Equipment One (1) Used Alpha Technologies Tensometer, Model Tensometer 2000, rubber tensile tester, year 2000,...
1051 Shaw 1 K5 143 Liter Litre Intermix Intermeshing Rotors Mixer One (1) used Shaw K5 Intermix Rubber Mixer, 143 Litre net chamber volume, 100 Liter batch size, Moto...
8037 Monsanto Flexsys 1 RPA 2000 RPA Rubber Process Analyzer Lab Equipment One (1) Used Monsanto Flexsys RPA 2000 83064 Rubber Process Analyzer. S/N: 90AIF2092. 120 Volts, 15 ...
2020 Farrel 1 6 x 13 150x330 Lab Mill DUAL DRIVE Mill One (1) Used Farrel Lab Mill, 6 x 13” (150 x 330) rolls, rubber mill, cabinet style, under-slung DUA...
1099 Dabsco 1 8ft Strip Cooler Batch-off One (1) Used Dabsco Rotary Drum Rubber Strip Cooler, batch-off, 10ft drum length, large capacity, id...
8036 Monsanto 1 ODR 2000 Rheometer Lab Equipment One (1) Used Monsanto Rheometer, Model ODR 2000, Oscillating Disc Rheometer designed to test the cur...
1007 Farrel 1 BR 1.6L Lab Mixer One (1) Used Model BR Farrel Lab Banbury Rubber Mixer, 2.6 lb. capacity, 96 cu. in net volume of mix...
1454 Farrel 1 BR 1.6L Lab Mixer Mixer Parts Item 1454 – One (1) Used Farrel BR spare body only, connecting gears and low speed coupling included...
1449 Farrel 1 F270 Linear Actuator Mixer Parts Item 1449 - One (1) Used Farrel Linear Actuator for Farrel F270 Mixer, 39T spline
8252 Alten 1 200 HP, 46.77 Parallel Shaft Gearbox Reducer One (1) Used Alten Gearbox, Model DG-990S-2-47, 46.77 reduction ratio, 300 HP Catalog Rating, 200 HP...
6556 Farrel 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Plastic Item 6556 - One (1) Used Farrel 4.5" (120mm) Plastic Extruder, 12:1 L/D, 125 HP 1750/2000 RPM 500 VD...
1017 Farrel 1 OOC 4.6 Liter Lab Mixer One (1) Used Farrel Banbury OOC Lab Rubber Mixer, 4.6 liter chamber, 4 lb. rubber capacity, jacketed...
8453 Lufkin 1 1400 HP 21.85:1 Unidrive F270 #11D Gearbox Reducer One (1) Used Lufkin model D890AH double reduction horizontal parallel shaft mixer speed reducer, arr...
6033 Monsanto 1 3 1/2" 90mm 3.5" 16:1 L/D Extruder Cold Feed One (1) Used Monsanto 3.5" 90mm Cold Feed Extruder, 16:1 L/D, 100 HP 500 VDC motor, vacuum vented sc...
6018 Royle 1 2 1/2" 60mm 2.5" 16:1 L/D Extruder Cold Feed One (1) Used Royle 2.5" 60mm Cold Feed Rubber Extruder, Model 1A, 16:1 L/D, no motor, roller feed
2651 Farrel 1 24" x 68" 600x1700 Calender Roll Rolls One (1) NEW Farrel 24x68” Calender Roll, drive roll, drilled for cooling, 177” OA length, designed f...
6060 NRM 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Cold Feed One (1) Used NRM 4.5" 120mm Cold Feed Rubber Extruder, 12:1 L/D, 25.14:1 G/B ratio, Reliance 100 HP,...
6013 Davis Standard 1 2 1/2" 60mm 2.5" 20:1 L/D Extruder Cold Feed One (1) DS Davis Standard 2.5" 60mm Cold Feed Rubber Extruder, Model 25IN25, 20:1 L/D, 17.26:1 G/B r...
6015 Davis Standard 1 2 1/2" 60mm 2.5" 20:1 L/D Extruder Cold Feed One (1) DS Davis Standard 2.5" 60mm Cold Feed Rubber Extruder, Model 25IN25H, 20:1 L/D, 17.26:1 G/B ...
6016 Davis Standard 1 2 1/2" 60mm 2.5" 20:1 L/D Extruder Cold Feed One (1) DS Davis Standard 2.5" 60mm Cold Feed Rubber Extruder, Model 25IN25DSREV, 20:1 L/D, 17.26:1 ...
6045 NRM 1 3 1/2" 90mm 3.5" 12:1 L/D Extruder Cold Feed One (1) NRM 3.5" 90mm Cold Feed Rubber Extruder, 12:1 L/D, 24.88:1 gearbox ratio, US Motors 75 HP 17...
2022-1 Bolling 1 10 x 24 250x600 Cabinet Style Mill One (1) Used Bolling 10 x 24 (250 x 600) Silicone Rubber Mill, chrome plated rolls, underslung chain...
1006 Farrel 1 BR 1.6L Lab Mixer Mixer One (1) Used Farrel Laboratory BR Banbury Mixer, S/N 65A4417, with 2.6 Lb. Capacity, 96 Cu. In Net V...
1016 Farrel 1 OOC 4.6L Lab Mixer Mixer One (1) Used Farrel OOC 8 Lb. Banbury Mixer, S/N 85A 1209, with 8Lb @ Specific Gravity of 1 Batch Ca...
6261 RMS 1 4 1/2" 120mm 4.5" 14:1 L/D Extruder Pin Barrel One (1) RMS 4.5" 120mm Pin Barrel Rubber Extruder, 14:1 L/D, 150 HP 1150 RPM 500 VDC motor, variable...
4050 Adamson 1 28 x 65 710x1650 Inclined Calender 2-Roll One (1) Used Adamson 28" x 65" 2-Roll Calender, 120-degree incline, GE 200 HP 1150 RPM 500 VDC motor...
1778 Farrel 1 F370 Rotors Unidrive Mixer Parts One (1) Rebuilt Farrel F370 rotor, right wing, 4-wing type, Banbury design, unidrive configuration
1745 Bolling #10 Rotors Bull Gear Mixer Parts One (1) Rebuilt set of Bolling #10 rotors, 2-wing, bull gear configuration
5031 McNeil 35 Passenger / LT Passenger / LT Tire Bladder Press Thirty Five (35) Bladder Molds for McNeil Model 900-30x36 Bladder Presses, suitable for passenger an...
7272 General Dynamics 1 200 HP AC Motor One (1) Used General Dynamics Electric Motor, 200HP AC, 585 RPM, 440 VAC, 250 Amps, 3/60, Frame 304B...
7111 Seimens 1 60 HP DC Motor One (1) Used Seimens Motor, 60HP, 1750/2100 RPM, 500 VDC, 60 cycle, DPFG-BV enclosure, 97.4 Amps
2640 Farrel 1 26" x 38" 650x965 Cracker Mill Roll Rolls One (1) Used Farrel 26” x 38” Cracker Mill Roll, rear drive roll, cored for cooling, 17” bushing jou...
2639 Farrel 1 26" x 38" 650x965 Cracker Mill Roll Rolls One (1) Used Farrel 26” x 38” Cracker Mill Roll, front roll, cored for cooling, 17” bushing journals...
1886 Farrel 1 F370 Floating Weight Mixer Parts One (1) Rebuilt Floating Weight for Farrel F370 Mixer
2667 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 15” co...
2668 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 15” co...
2669 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 15” co...
2670 Farrel 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Farrel 26” x 84” Mill Roll, front roll, cored for cooling, 17” bushing journals, 14” co...
2671 Farrel 1 26" x 84" 650x2100 Mill Roll Rear Corrugated Rolls One (1) Used Farrel 26” x 84” Mill Roll, rear roll, cored for cooling, 17” bushing journals, 15” con...
2672 Farrel 1 26" x 84" 650x2100 Mill Roll Rear Corrugated Rolls One (1) Used Farrel 26” x 84” Mill Roll, rear roll, cored for cooling, 17” bushing journals, 15” con...
2620 Farrel 1 8" x 16" 200x400 Mill Roll Rear Rolls Item 2620 - One (1) Used Farrel 8” x 16” Mill Roll, rear roll, cored for cooling, smooth surface
2638 Farrel 1 21" x 36" 530x915 Refiner Mill Roll Rolls Item 2638 - One (1) Used Farrel 21” x 36” Refiner Mill Roll, front roll, cored for cooling, smooth s...
2643 Farrel 1 16" x 42" 400x1066 Mill Roll Rear Rolls Item 2638 - One (1) Used Farrel 16” x 42” Mill Roll, rear drive roll, cored for cooling, smooth surf...
6046 NRM 1 3 1/2" 90mm 3.5" 8:1 L/D Extruder Cold Feed One (1) NRM 3.5" 90mm Cold Feed Rubber Extruder, 8:1 L/D, 20.64:1 gearbox ratio, Reliance 50 HP 1750...
6047 NRM 1 3 1/2" 90mm 3.5" 12:1 L/D Extruder Cold Feed One (1) Used NRM 3.5" 90mm Cold Feed Rubber Extruder, 12:1 L/D, 24.9:1 G/B ratio, US Motors 75 HP DC...
6063 NRM 1 4 1/2" 120mm 4.5" 12:1 L/D Extruder Cold Feed One (1) Used NRM 4.5" 120mm Cold Feed Rubber Extruder, 12:1 L/D, Reliance 125 HP, 1200 RPM, 500 VDC ...
1070 Farrel 1 #9D 180 Liter Litre Tangential 2-Wing Mixer One (1) Used Farrel #9D Banbury Rubber Mixer, 180 liter, Farrel heavy duty unidrive gearbox 20.68:1,...
4055 Bolling 1 28 x 72 710x1825 Inclined Calender 2-Roll One (1) Used Stewart Bolling 28" x 72" Inclined Heavy Duty Calender, S/N 13092, with (2) 28" x 72" P...
6715 Readco 1 5" 125mm Twin Screw Extruder Twin Screw One (1) Used Readco S/S Extruder, Machine 5 Inch C.P., S/N 108530, Some S/S Spare Parts, Includes (2...
7309 General Electric 1 300 HP DC Motor One (1) Used GE General Electric Motor, 300 HP, 880 RPM, 500 VDC, 485 Amp, Type CD685AS, Enclosure D...
1024 Moriyama Sanyu 1 55 Liter Litre Tilt Kneader Mixer Item 1024 – One (1) Used Moriyama Sanyu 55L Liter Litre Tilt Mixer, model DX55-200, 200 HP, 1170 RPM...
9021 Doss 2 10-55mm Frame Field O-Ring Gasket Sorting Machine One (1) Used Doss dSort3 O-ring & Gasket sorting machine, designed by Doss Visual Solution is an aut...
6558 Flender 1 6" 150mm 30:1 L/D Extruder Plastic One (1) Used Flender 6" (150mm) Plastic Extruder, 30:1 L/D, no motor, direct drive, lowboy gearbox, ...
4022 Farrel 1 24 x 66 610x1675 Vertical Calender 3-Roll Item 4009 - One (1) Used Farrel 24” x 66” (600 x 1675) 3-Roll Rubber Calander, rolls are cored for c...
9041 Groen 1 40 Quart Kettle Blender Food Grade One (1) Used Groen Jacketed Steam Kettle TDB/7-40 on Stand with Blender / Mixer, 40 Quart, 10 gal, 4...
9051 Edwards 1 1-Ton Liquid Chiller One (1) Used Edwards Liquid Chiller, 1-Ton, Model CF-0200-A, 208/230 VAC, 250-400 PSI, Refrigerant R...
8910 Farrel 1 BR 1.6L Lab Mixer Lab Equipment One (1) Used Farrel Laboratory BR Banbury Mixer, S/N 65A4417, with 2.6 Lb. Capacity, 96 Cu. In Net V...
8911 Farrel 1 BR 1.5L Lab Mixer Lab Equipment One (1) Used Model BR Farrel Lab Banbury Mixer, 2.6 lb. capacity, 96 cu. in net volume of mixer cham...
8912 Farrel OOC 4.6L Lab Mixer Lab Equipment One (1) Used Farrel OOC 8 Lb. Banbury Mixer, S/N 85A 1209, with 8Lb @ Specific Gravity of 1 Batch Ca...
8913 Farrel 1 OOC 4.6L Lab Mixer Lab Equipment One (1) Used Farrel Banbury OOC Lab Mixer, rubber mixer, 4.6 liter chamber, 4 lb. rubber capacity, j...
8914 Bolling 1 OM 1.6L Lab Mixer Lab Equipment One (1) Used_Bolling_Lab_Banbury_Mixer, 1.6 liter, 2.6 lb.capacity, 96 cu. in net volume of mixer ch...
2695 Bolling 1 32"x120" 810x3050 Calender Roll Rolls One (1) Used Bolling 32” x 120” Calender Roll, driven roll, cored for cooling, sleeve bushing journa...
2696 Bolling 1 32"x120" 810x3050 Calender Roll Rolls One (1) Used Bolling 32” x 120” Calender Roll, drive roll, cored for cooling, sleeve bushing journal...
2647 Farrel 1 24 x 48 610x1220 Mill Front Roll Rolls One (1) Used Farrel 24” x 48” Mill Roll, front roll, cored for cooling, sleeve bushing journals, smo...
2648 Farrel 1 24 x 48 610x1220 Mill Rear Roll Rolls One (1) Used Farrel 24” x 48” Mill Roll, rear roll, cored for cooling, sleeve bushing journals, smoo...
8052 Farrel 1 6 x 13 150x330 Lab Mill Lab Equipment One (1) Used Farrel Rubber Lab Mill, 6 x 13”, 150mm x 330mm, rubber mixing mill, cabinet style, unde...
1030 Taiwan 1 75 Liter Litre Kneader Tilt Mixer One (1) Used Taiwan 75 Liter Tilt Mixer, Kneader type, 150 HP, 480 VAC motor, tilt discharge, direct...
1045 Farrel 1 F80 80 Liter Litre Tangential 4-Wing Mixer One (1) Used Farrel F80 Banbury Rubber Mixer, 80 liter, fully stellited 4-wing tangential rotors, Lu...
7124 Cutler 1 100 HP DC Motor One (1) Used Cutler Motor, 100HP DC, 1750 RPM, 500 Volts, 161 Amps
8267 Hansen 1 300 HP 25.73:1 Parallel Shaft Gearbox Reducer Used Sumitomo Hansen Model RDK313BM-25 Gearbox Reducer, 300 HP / 220 KW service rating, 25.733:1 red...
2661 Adamson 1 24" x 84" 600x2100 Mill Roll Rear Rolls One (1) Used Farrel 24” x 84” Mill Roll, rear roll, cored for cooling, 17” bushing journals, connect...
2662 Adamson 1 26" x 84" 650x2100 Mill Roll Front Rolls One (1) Used Adamson 26” x 84” Mill Roll, front roll, DRILLED for cooling, 17” bushing journals, con...
1080 Farrel 1 F270 270 Liter Litre Tangential 2-Wing Mixer One (1) Farrel F270 Unidrive Mixer, 2-wing rotors, Toshiba 1000 HP @ 1180 RPM 4160 VAC single speed ...
2551 Adamson 1 84" Blender Roll Mill Parts One (1) Used Blender Roll for 84” Rubber Mill, mechanical yankee screw style
1977 Torit 1 2 HP Dust Collector Dust Collector One (1) Used Torit 3 HP Dust Collector, Model 84, 230/460 VAC, Serial No. C6565
1456 Farrel 1 #9D 180 Liter Litre Body Chamber Mixer Parts One (1) Used Farrel #9D unidrive chamber only, 180 liter capacity, 2-wing rotors, FYH dust stops, S/...
1457 Farrel 1 #9D 180 Liter Litre Body Chamber Mixer Parts One (1) Used Farrel #9D unidrive chamber only, 180 liter capacity, 2-wing rotors, FYH dust stops S/N...
7333 General Electric 1 600 HP AC Motor One (1) Used GE Motor, 600 HP, 890 RPM, 440 VAC, 727 amps, foot mounted, frame 8407S
1941 Farrel 1 Banbury Rotac Actuator Mixer Parts One (1) Rebuilt Farrel Rotac Rotary Actuator for Banbury Mixers, hydraulic type, door actuator
5172 L&T Larsen & Toubro 3 104" 2700-104 OTR Tire Press Mechanical Three (3) Used L&T Larson & Toubro 104” OTR Mechanical Tire Curing Press, Model 2700-104 L4-TCP, 120...
5178 GRM Guilin Rubber 1 6500-170" OTR Tire Press Hydraulic One (1) Used GRM Guilin Rubber Machinery 170” Giant OTR Hydraulic Tire Curing Press, Model 6500-170,...
4170 Comerio 1 20 x 54 500x1370 "S" Type STEEL.CORD.LINE Calender 4-Roll One (1) Used Comerio Ercole Steel-Cord Calender Line, complete pre-calender section with 2x 250mm co...
4171 Comerio 1 24 x 72 610x1900 "S" Type INNER.LINER TEXTILE Calender 4-Roll One (1) Used Comerio Ercole Inner liner & Textile Calender Line, complete pre-calender section with ...
5303 TST 1 57" - 63" Radial Giant OTR Tire Building Machine One (1) Used TST Unistage All-Steel Radial Giant OTR Tire Building Machine, Uni-stage, model TST-LCZ...
5362 TST 1 1100mm Steel Cord Tire Cutter Steel Cord One (1) Used TST High Angle Steel Cord Cutter for Tire Production, 17-36 degree cut, 1100mm max cutt...
6328 Farrel 1 15" 300mm Drop Extruder Extruder Dump Item 6328 - One (1) Used Farrel 15” Dump Extruder, drop extruder, hot feed extruder, 95:1 total gear...


Building quality tires is not for amateurs. The end product may seem simple, but the process of developing that product is anything but! Building quality tires is a complex process that calls for sophisticated machinery. Formulating and then mixing the rubber compound is just the beginning. There’s also the preparation of the cord, the calendering steps for belt, ply, and the innermost layer of the tire. Next come the bead component preparation and the extrusion of tread and sidewall.

 

Only then can the tire building truly proceed. This is in itself is an involved process. The wrapping of inner liner and ply is followed, one stage at a time, by the application of the bead assemblies, sidewall, belts, cap, and tread. As you move through each of these steps, the quality of the machinery really starts to tell. By the time you get to the curing process, it’s obvious—a quality tire depends on a quality tire building machine.

 

At Soberay and Sons, we’re known for the high quality used tire machinery that we sell. We search the globe to bring you the highest quality of secondhand tire machinery available. We offer the most valued name brands and we aim to provide machine coverage for every step of the process. Looking for a McNeil & NRM tire press, McNeil & NRM tire building machine, or McNeil & NRM rubber extruder? We carry them, along with other leading name brands like Farrel, Bolling, Werner & Pfleiderer, Kobelco, and more.

 

Search our inventory for the brand that interests you and review the details. You can also click on any item number to access multiple photos. At Soberay and Sons, we take pride in delivering value. That’s why we’re selective about our machinery and competitive about our pricing. We’ve built our reputation on a 70-year history of superb customer service.